Compose your Aquastation based on your needs!

What kind of Aquastation do you prefer? With larger capacity you can store more historical data (water values, state of the electrical lines, statistics, etc ..). Moreover, a greater capacity corresponds to a faster and higher quality data storage device.

With two redundant probes you can calculate the average between the values (very useful in the case of tanks larger than 300 litres with different temperature zones) and notice calibration problems of one of the two probes.

The AquaStation is configurable through a web interface, is updated through Internet and sends e-mail alerts regarding the data collected by the installed probes (too low temperature, insufficient heating, out of threshold PH, excessive energy consumption, etc ..). The basic AquaStation is equipped with a USB ethernet RJ45; however this module allows connection to a wireless network, thus avoiding to bring network cables on the module.

Remote IR Control can perform a shortcuts.

The module allows you to control 4 independent LED lines, by scheduling sunrise, sunset and maximum brightness of the line (1-100%) in steps of about 0.4% (1/256). Ideal for LED strips. With the BioDimmer, you can reproduce the light and photoperiod conditions of the chosen biotope.

Manage your circulation pumps 1-10v PWM simulating tides and circulate the water of your aquarium planning increasing, stationary and decreasing powers in steps of 1/256.

This module can calculate consumption, relating it to the ignition of lamps, heaters and to the external temperatures. It can generate graphs on a daily, weekly or monthly basis helping you save energy.

Compatibly with optional modules chosen, the colour 1.6'' LCD screen allows for real-time display of all values of water, the status of the lines (led and 220v) and allows you to access a set of important information (AcquaStation IP address, advances, etc ..). This equipment is strongly recommended because it allows you to immediately detect outside threshold values or any anomaly thanks to the colours.

Compatibly with optional modules chosen, the colour 3.2'' TouchScreen allows for real-time display of all values of water, the status of the lines (led and 220v) and allows you to access a set of important information (AcquaStation IP address, advances, etc ..). This equipment is strongly recommended because it allows you to immediately detect outside threshold values or any anomaly thanks to the colours. Unlike the LCD simple Display, the TouchScreen Display has higher resolution, allows show some graphics and allow to setting parameters. This module requires a 16Gb AquaStation Base to run correctly.This equipment is strongly recommended because it allows you to immediately detect outside threshold values or any anomaly thanks to the colours.

The timer allows you to control 7 linear 220V sockets by setting on/off function according to a schedule. Moreover, the module allows you to take action upon certain conditions according to the settings you have chosen (switch on the heater if the temperature drops below a threshold, turn the solenoid CO2 if the pH rises above a threshold, etc ..).

With the pH probe you can obtain real-time PH values, control a 220V solenoid valve to activate your CO2 system (solenoid and system not included) and receive email alerts in case of out of threshold values. Together with the probe you will also receive the liquid buffer to store your probe or for the calibration (recommended every 2 years).

With the flooding/level probe, the AquaStation will measure the water level inside the analysis box and will send you an email alert in case of problems; moreover, if set, it will turn off/on a 220v socket.

The energy analysis module, the display, the LED Dimmer module and the conductivity module are connected via BUS. If you run out of space, you will need to purchase a Hub able to extend the BUS of two doors.

The Aquastation Cloud allows you to: save your online backup on our servers check in real time your aquarium values on any device (apple, android, windows, etc ..) using our servers receive weekly or monthly system updates adding functionality and making more user-friendly the programming and management interfaces receive email feedback in case of questions or problems in configurations activate the "CloudAlert" function that alert you in case your AquaStation is unattainable (absence of electrical power, system failure, accidental disconnection of accessories, etc ..).

With the extension of the extra warranty, we will replace the AquaStation (and every accessory you have purchased), even in case of electric shock (not included in the standard warranties).